Very large trees can often be moved with safety. It is essential that the transplanting be done when the trees are perfectly dormant, - winter being preferable, - that a large mass of earth and roots be taken with the tree, and that the top be vigorously cut back. Large trees are often moved in winter on a stone-boat, by securing a large ball of earth frozen about the roots. This frozen ball is secured by digging about the tree for several days in succession, so that the freezing progresses with the excavation. A good device for moving such trees is shown in Fig. 14S. The trunk of the tree is securely wrapped with burlaps or other soft material, and a ring or chain is then secured about it. A long pole, b, is run over the truck of a wagon and the end of it is secured to the chain or ring upon the tree. This-pole is a lever for raising the tree out of the ground. A team is hitched at a, and a man holds the pole b.

144. Pruned young tree.

145. Pruned young tree.

146. Peach tree.

147. Peach tree pruned for planting.

Other and more elaborate devices are in use, but this explains the idea and is therefore sufficient for the present purpose ; for when a person desires to remove a very large tree he should secure the services of an expert.

The following more explicit directions for moving large trees are by Edward Hicks, who has had much experience in the business, and who made this report to the press a few years ago: ge trees, say those ten to diameter and twenty-five high, it is well to prepare oing and cutting or sawing a proper distance from the ix to eight feet, in June, heal over and send out s, which should not be in-than is necessary in moving next fall or spring. Young, raples and elms, originally from the nursery, do not need such preparation nearly as much as other and older trees. In moving a tree, we begin by digging a wide trench six to eight feet from it, leaving all possible roots fast to it. By digging under the tree in the wide trench, and working the soil out of the roots by means of round or dull-pointed sticks, the soil falls into the cavity made under the tree. Three or four men in as many hours could get so much of the soil away from the roots that it would be safe to attach a rope and tackle to the upper part of the trunk and to some adjoining post or tree for the purpose of pulling the tree over. A good quantity of bagging must be put around the tree under the rope to prevent injury, and care should be taken that the pulling of the rope does not split off or break a limb.

A team is hitched to the end of the draft rope, and slowly driven in the proper direction to pull the tree over. If the tree does not readily tip over, dig under and cut off any fast root. While it is tipped over, work out more of the soil with the sticks. Now pass a large rope, double, around a few large roots close to the tree, leaving the ends of the rope turned up by the trunk to be used in lifting the tree at the proper time. Tip the tree in the opposite direction and put another large rope around the large roots close to the trunk; remove more soil and see that no roots are fast to the ground. Four guy-ropes attached to the upper parts of the tree, as shown in the cut (Fig. 149), should be put on properly and used to prevent the tree from tipping over too far as well as to keep it upright. A good deal of the soil can be put back in the hole without covering the roots to get it out of the way of the machine. The latter can now be placed about the tree by removing the front part, fastened by four bolts, placing the frame with the hind wheels around the tree and replacing the front parts.

Two timbers, three-by-nine inches, and twenty feet long, are now placed on the ground under the hind wheels, and in front of them, parallel .to each other for the purpose of keeping the hind wheels up out of the big hole when drawing the tree away; and they are also used while backing the hind wheels across the new hole in which the tree is to be planted. The machine (Figs. 149,150) consists of a hind axle twelve feet long, and broad-tired wheels. The frame is made of spruce ■ three-by-eight inches and twenty feet long. The braces are three-by-five inches and ten feet long, and upright three-by-nine inches and three feet high; these are bolted to the hind axle and main frame. The front axle has a set of blocks bolted together and of sufficient height to support the front end of the frame. Into the top timbers, three-by-six inches, hollows are cut at the proper distances to receive the ends of two locust rollers. A windlass or winch is put at each end of the frame, by which trees can easily and steadily be lifted and lowered, the large double ropes passing over the rollers to the windlasses. A locust boom is put across the machine under the frame and above the braces; iron pins hold it in place. The Bide guy-ropes are made fast to the ends of this boom.

The other guy-ropes are made fast to the front and rear parts of the machine. Four rope loops are made fast inside of the frame, and are so placed that by passing a rope around the trunk of the tree and through the loops two or three times, a rope ring is made around the tree that will keep the trunk in the middle of the frame and not allow it to hit either the edges or the rollers - a very necessary safeguard. As the tree is slowly lifted by the windlasses, the guy-ropes are loosened, as needed. The tree will pass obstructions, such as trees by the roadside, but in doing so it is better to lean the tree backward. When the tree has arrived at its new place, the two timbers are placed along the opposite edges of the hole so that the hind wheels can be backed over it. The tree is then lowered to the proper depth, and made plumb by the guy-ropes, and good, mellow soil is thrown in and packed well into all the cavities under the roots. When the hole is half filled, several barrels of water should be poured in; this will wash the soil into the cavities under the center of the tree much better. When the water has settled away, fill in and pack the soil till the hole is little more than full. Leave a depression, so that all the rain that may fall will be retained.

The tree should now be judiciously trimmed and the machine removed. Five men can take up, move, and plant a tree in a day, if the distance is short and the digging not too hard. The tree should be properly wired to stakes to prevent the wind from blowing it over. The front part of the machine is a part of our platform spring market-wagon, while the hind wheels are from a wood-axle wagon. A tree ten inches in diameter, with some dirt adhering to its roots, will weigh a ton or more".

148. Moving a. large tree.

149. The tree ready to lift.

150. The tree ready to move.